Manufacturing capicity of 2000 MVA/Annum

FAQs


Can a Twin-Path® sling be used in a fitting or trunnion which is less than the sling's width?
Yes, A Twin-Path® Sling can fit spaces half of their catalog width with no reduction in capacity. There are two dimensions, called Nominal Body Width, in the Twin-Path® section of the catalog. The larger dimension is the flat tube measurement before installing the core yarn. The smaller dimension is the approximate reduction in width you can expect to achieve when placing the sling in a smaller fitting. The paths of the Twin-Path® sling should be squeezed together to reduce the dimension – DO NOT fold one path over the other to create a reduced dimension.
 

 

What is the Check-Fast® inspection system?
 The Check-Fast® inspection system with External Warning Indicator (EWI) provides for a pass/ fail inspection of the internal load bearing core yarn. Damage to the core yarn from ultraviolet (UV) light degradation, fiber on fiber abrasion, fatigue, and severe overload can be detected. If the sling is mistakenly overloaded beyond rated capacity the EWI is designed to disappear before the sling fails. The sling inspector now has a GO/NO-GO inspection device rather than relying on a subjective hand-over-hand inspection to make an educated guess if the load bearing core yarns are in good condition. If the EWI is not visible, remove the sling from service and send to the manufacturer for repair evaluation. This safety system is available for High Performance K-Spec® Fiber Roundslings or polyester roundslings fabricated by authorized Slingmax® dealers

 

What is the difference between the Check-Fast® inspection system and Tell-Tails?
Tell-Tails are extensions of the core yarn bundles and are designed to function as overload indicators. The tails are designed to retract and eventually disappear if the sling is overloaded. Tell-Tails should extend past the tag area of each sling. If both Tell-Tails are not visible remove the sling from service and send to the manufacturer for repair evaluation. This inspection system also combines use of a fiber optic cable. The condition of the internal load bearing core yarn can be inspected by checking the continuity of the fiber optic cable. If crushing, cutting, heat or chemical damage has occurred then the damage to the fiber optic cable will destroy its ability to transmit light from one end to the other, giving the inspector a reason to remove the sling from service and send it in for repair evaluation. (Though not required the fiber optic inspection system is also an option with the Check-Fast® system).

 

What pin diameter or hardware diameter is OK with a Twin-Path® Sling?
The Slingmax® statement on hardware is in the ‘Mechanical Considerations’ section of our catalog. Item #7 states “Slings used with fittings shall be compatible with the fittings used. The lifting capacity shall be rated at the lower of the sling or fitting. Fitting openings shall be of the proper shape and size to assure that the sling will seat properly”. In other words, the diameters of most commercially available hardware are sufficient for use with a Twin-Path® sling of equal capacity.

 

What happens if oil or gasoline gets on my Twin-Path® Sling?
Hydrocarbons and oils do not affect the performance of any Twin-Path® sling. Please reference the chart for Chemical Resistance of K-Spec® core yarn for additional information. Twin-Path® slings with Covermax® jackets may be cleaned using a commercially available mild detergent and ambient temperature water, then allowed to air dry.
.

 

Do Twin-Path® slings stretch? I’ve seen loads bounce with synthetic slings?
At rated capacity nylon slings will stretch up to 15%. Round slings made with Polyester core yarn will stretch 3%. Braided Polyester slings will stretch 9%. Twin-Path® Extra slings with K-Spec® core yarn stretch less than 1% at rated capacity, about the same as wire rope slings

 

If a synthetic roundsling has one interior core yarn which has been damaged or cut, can it still be used if the sling’s capacity is de-rated??
NO! Roundslings that suffer damage to the load bearing fibers must be removed from service. These slings shall be destroyed to prevent inadvertent use.

 

If the cover on a Twin-Path® sling is damaged can it be repaired?
Yes. The Covermax® cover is actually comprised of two covers – a green outer cover and a red inner cover. As long as there is no damage to the core yarns the cover may be safely repaired. With the Twin-Path® design our manufacturers can repair the cover without the risk of sewing over the internal core yarns during repair.

 

If a synthetic roundsling has one interior core yarn which has been damaged or cut, can it still be used if the sling’s capacity is de-rated??
NO! Roundslings that suffer damage to the load bearing fibers must be removed from service. These slings shall be destroyed to prevent inadvertent use.

 

Are all Twin-Path® Extra Slings proof tested before reaching the customer?
Yes. As part of our manufacturing process each Twin-Path® sling is proof tested to two times its vertical rated capacity. In addition, every repaired Twin-Path®sling is also proof tested before it is returned to the customer.

 

Can I overlap Twin-Path® slings in a shackle or other hardware?
Yes. The paths should be laid directly on top of each other to prevent possible tearing of the Covermax® jacket.

 

What is the difference between abrasion protection and cut protection?
Abrasion protection is needed when the sling is wrapped around a load which is rough, dirty or gritty. Slingmax® abrasion protection products include Synthetic Armor™ (Synarm) Pads and shackle pin pads. Cut protection is needed when there is an edge or corner that the sling may come in contact with. Slingmax® cut protection devices include the CornerMax® pad and CornerMax® sleeves, engineered devices designed to provide cut protection up to 25,000 lbs. per inch of sling width.

 

Can I use a Synthetic Armor Pad for cut protection?
No. Synthetic Armor Pads are intended for abrasion protection or to increase the diameter of a bearing surface. If cut protection is required we recommend the use of the CornerMax® products.   3. How do I know if a load edge is "sharp" enough to require a CornerMax Pad?
The word "sharp" is considered subjective and is no longer used in our catalog or website. CornerMax Pads should be utilized to protect the sling from all edges and corners.

 

Why use a multi-part wire rope sling instead of a single-strand wire rope sling?
A single strand sling is less flexible than a multi-part wire rope sling. Also, a multi-part wire rope sling provides a better D/d ratio.
.

 

Are the D/d ratios for the Slingmax® wire rope slings based on component diameter?
No. The D/d ratios are based on the finished diameter. Finished and component diameters for each wire rope sling may be found on the respective catalog page for each item.

 

What are the reductions for the Slingmax® wire rope slings if you are not able to use the correct D/d?
Approximate reductions for the sling body are as follows:
                       5:1                        100%
                       4:1                        92%
                       3:1                        84%
                       2:1                        73%
                       1:1                        65%
                       Less than 1            50%

 

What is the difference between a Gator-Max® and a Gator-Laid® sling?
Gator-Max® is hand-spliced, Gator-Laid® is made using swaged sleeves.

Products

  • Polyester Slings

  • Clamps

  • Lifting & Rigging

  • Load Securing Equipments

  • Material Handling Accessories

  • Turnover Devices

  • Wire Rope & Wire Rope Slings

Contact Us

Follow us on Facebook

Copyright © 2013 KRYFS Manufacturers. All Rights Reserved.